| 加工定制：否 | 品牌：祥瑞 | 种类：自动衣架成型机 |
| 型号：无 | 别名：衣架机 | 用途：生产衣架 |
| 电动机功率：1.5/3（kw） | 外形尺寸：18（mm） | 重量：0.75（t） |
自动衣架成型机
Automatic Clothes Rack Making Machine
使用说明书
Operating Instruction
(请仔细阅读)
(Please read carefully)
机器性能和特点：
本机器为自动衣架成型机，可以制造出各类不同形状和尺寸大小各异的衣架.其产量为每分钟28只.铁丝直径为1.6~2.7MM读性。其中镀锌铁丝衣架,衣架尺寸:13寸,14寸,15寸,16寸,18寸,20(包括16寸~18寸君子衣架).电压为380伏三厢式220伏二厢都可试用.380伏电机1.5千瓦220伏电机3千瓦.机器净重750千克.放丝架和收集衣架架.
操作说明:
一:开关分成三种色(红色,绿色,黑色).其中黑色按钮起点动作用,绿色按钮为正常开机,红色按钮为停机状态.
二:松开调直合金螺钉和调直轮手柄,将线材送入送线主动轮和送线压紧轮之间,调节送线压紧轮手柄,按"送线"按钮将线材引入成型模具内.按"切断"按"成型"按钮,即可手动成型衣架成品,均可正常开机.
Functions and Characteristics
This machine is automatic clothes rack making machine, which can make clothes racks of all shapes and sizes. It can produce 28 clothes rancks per minute. Diameter of iron wire between 1.6~2.7mm is ok. The size of clothes racks can be 13 inches, 14 inches, 15 inches, 16 inches, 18 inches and 20 inches. 380v and 220v is the proper valtage for the machine. The net weight of the machine is 750 kilograms.
Operating Instruction
First, buttons are divided into three colors(red, green, black). The black button is to start the machine. The green button indicates the normal operating process and red is to stop.
Second, loosen the straightening bolt and straightening wheel handle, then put the material between the wire delivery leading wheel and wire delivery pressing wheel. After that, adjust the handle of wire delivery pressing wheel,and then press the button to transport the material into the shape mould. Finally, press the "stop" and "done" buttons, thus clothes racks are made.
机器的日常维护:
一:机器不工作时请切断电源,禁止长时间通电不使用.
二:每班加油2次,加在各种油眼内,均可开机试用.
三:定期(2个月)检查减速箱内油量.油量不够时,请加够齿轮机油.
四:本机必须保持干净,干燥,且通风.
五:定期对传动部分(活动机构齿轮等)加油.
整机构成:
一:(机械)控制箱设有点动前进和快速前进.
二:本机送线轮,调直轮,成型模具等采用优质合金钢,并通过真空热处理,其耐磨性高,使用寿命长,轴类全部采用40CR或45#钢,并经调质处理,使其综合机械性能高,齿轮则全部采用锻坯,经调质及齿面高频淬火,硬度高达HRC55-58度.
Routine Maintanance
First, cut off the power supply when work is finished, DO NOT suppply the machine with power for long time while it is out of use.
Second, oil it twice every, then it can start work.
third, examine the oil mass in the reduction gear box every two months. If the oil mass is low, please add machine oil.
Forth, the machine must be kept clean, dry, and ventilated.
Fifth, oil the transmission part regularly.
components of the machine
First, there are buttons which can control the speed easily in the controling box.
Second, the wheels for wire delivery and for strightening, as well as the shape mould are made of quality alloy steel. As it has been through vacuum heat treatment, it enjoys the quality of good abrasion resistence and long service life. Axes are made of 40CR or 45# steel, and have been specially hardened and tempered, which improved the intergrated capability. Gear wheels are made of forging stock, the rigidity can reach HRC55-58 because of the hardening and tempering and high-frequency quenching.